The ResMed AirFit™ N30i features an innovative tube design that positions the tube at the top of the head. Instead of coming up from below, air is delivered from the CPAP machine through a SpringFit frame. The majority of the tubing is behind you, giving you the ability to sleep on your front or any side comfortably.

Sleep the way you want:

ResMed AirFit N30i features a top-of-the-head tube design that makes it easier to sleep in any position. The nasal cradle cushion sits comfortably under the nose rather than over the nasal bridge – great for side or stomach sleepers.

Get closer to your partner:

Sleep more freely and closer to your bed partner. With no front-end tube, the mask stays out of sight and out of the way.

Simplify your bedtime routine:

The mask is specially designed to slide quickly on and off to make your bedtime routine easier. The quick-release elbow makes it easy to disconnect mask from tubing if you need to get up at night.

Sizing frame:

1. If you are male, start with the standard frame size. If you are female, start with the small frame size.

2. If you try the standard size first, and the frame sits too close to your ears, size down to the small frame for a better fit.

3. If the frame is too large, try the small size frame for a better fit.

4. If you try the small frame first and the frame sits too close to your eyes, size up to the standard frame for a better fit.

5. If the frame is too small, try the standard size frame for a more comfortable fit.

First Night Assembly:

1. Ensure you have all the mask components and parts together.

2. Connect the elbow to the frame.

3. Thread the left end of the headgear into the left side of the frame and fasten the tab.

4. Thread the right end of the headgear into the right side of the frame and fasten the tab.

5. Align the arrow on the cushion to the arrow on the frame and connect together.

6. Connect the remaining end of the cushion and frame together with the ResMed logo facing the right way up through the headgear.

Fitting:

1. Bring the mask above your head and then down over your face while ensuring the elbow is centered on the top of your head.

2. Place the headgear behind your head and the cushion under your nose.

3. Adjust the headgear until the mask and cushion are comfortable.

4. Disconnect the elbow from the top of the frame and attach it to the air tubing.

5. Reconnect the elbow with the air tubing to the top of the frame.

Disassembly:

1. Ensure your mask is disconnected from your machine.

2. Pull the cushion out from one end of the frame.

3. Pull the cushion out from the other end of the frame.

4. Unfasten the headgear tab from one side and pull it out of the frame.

5. Unfasten the headgear tab from the other side and pull it out of the frame.

6. Squeeze the side buttons on the elbow and pull up to release it from the frame.

Managing leak:

1. Locate where the air is escaping from, which is typically above or below the cushion. Note, there is an intentional vent on the front of the cushion where air will flow through. This is normal. If air is escaping, this is typically above or below the cushion.

2. Adjust the cushion by gently pulling it away from your face and letting it reseal itself.

3. Adjust the headgear as needed to achieve a more secure seal.

4. Check that the frame is secure and that the mask elbow and tubing are not pulling on the mask.

Daily cleaning:

1. Take the cushion off the frame as per disassembly instructions.

2. Soak the cushion in warm water and a mild liquid detergent.

3. Clean the cushion and its vent holes inside and out with a soft bristle brush.

4. Rinse the cushion thoroughly under running tap water.

5. Leave the cushion to air dry away from direct sunlight.

Weekly cleaning:

1. Disassemble the mask into its components as per disassembly instructions.

2. Soak each of the components (headgear, elbow and frame) in warm water and a mild liquid detergent.

3. Clean the elbow and frame with a soft bristle brush and the headgear with your hands.

4. Rinse each of the components thoroughly under running tap water.

5. Squeeze the headgear and the sleeves on the frame with a clean towel to remove excess water.

6. Leave each of the components to air dry away from direct sunlight.